Industrial Roofing in Leander, TX
Warehouse, plant and pre-engineered metal building roofs that keep the operation dry and the production line running, installed from our Leander shop and out across TX, every job backed by a lifetime workmanship warranty.
A roof that does not stop your facility
An industrial roof is not a house roof made bigger. It sits over equipment, inventory and people on the clock. When it leaks, it shuts down a packing line, soaks a pallet of product, or trips the electrical in a panel that runs the whole floor. That is the difference we plan around on every warehouse, plant and distribution building we touch.
We work on pre-engineered metal building roofs, standing-seam and exposed-fastener metal over steel framing, and the large low-slope membrane fields you find on most warehouses across TX. We do it the right way instead of trying to make a quick nickel, which on an industrial roof means phasing the work so your operation keeps moving, detailing every curb, vent and rooftop unit so water has nowhere to pool, and leaving you a roof your maintenance team can actually keep up.
Tell us about the building and you get a free roof quote with the system, the field square footage and the warranty spelled out in plain language, plus a phasing plan that fits how the facility runs.
Pre-engineered metal building roof
How we re-roof an industrial building
We get on the roof and map the whole field
Before any number, we walk the entire roof field, the steel structure where we can see it, and every penetration: exhaust fans, makeup-air units, skylights, gas lines and electrical curbs. On a large building those penetrations are where most leaks start, so we photograph and mark every one and read the slope to find the ponding spots.
We build a phasing plan around your operation
A facility cannot shut its doors for a re-roof. We section the roof so the crew works over empty or low-activity bays first, keep the building dry-in overhead at the end of every workday, and schedule the loud and disruptive work for off-shift hours where it matters. You stay running while the roof goes on.
Tear-off or recover, deck and structure repair
Depending on the existing roof and the building code, we either tear off to the deck or recover over a sound substrate. We replace corroded metal deck, re-fasten loose panels, and shore up any structural issue we uncover before the new system goes down. The part you never see again is the part that decides whether the roof holds.
System, flashing, ventilation and the warranty
We install the metal or membrane system the building calls for, flash every curb, parapet and unit so the field drains clean, and finish the ventilation to our Lomanco-certified design so the attic or plenum breathes. Then we sweep the property with a magnet for stray fasteners and hand you the lifetime workmanship warranty plus six years of annual weatherproofing.
Metal building roofs, membrane fields, and which your facility needs
Most of the industrial buildings we roof across TX fall into two camps, and they get handled differently. Pre-engineered metal buildings, the steel-frame warehouses and shops with a metal roof over open purlins, want a metal system: either re-securing and re-coating the existing standing seam, or a full panel replacement when the metal has rusted through or the fasteners have backed out across the field. On these buildings the leaks almost always start at the lap seams and the screw gaskets, not in the middle of a panel, so a good crew chases those details instead of just throwing new metal at the problem.
The second camp is the large low-slope warehouse with a single-ply membrane field, the wide flat-looking roofs you see on distribution centers and plants. Those fail at the seams, the rooftop unit curbs and the drains, and they fail quietly: water tracks under the membrane and rots the insulation and deck for months before it ever drips inside. That is why an industrial roof needs eyes on it every year, well before it finally leaks, and it is the reason our six years of included annual weatherproofing matters more on a commercial building than almost anywhere else. We check the seams, the curbs and the drains and seal what has moved before it costs you a deck.
An industrial roof needs eyes on it every year, well before it finally leaks.
Plenox · 6 years of weatherproofing, done annuallyDrainage is the other thing that separates a roof that lasts from one that ponds. A flat-looking industrial field still has to shed water to the drains and scuppers, and standing water is what kills membrane and corrodes metal early. When we re-roof a facility we correct the slope to the drains wherever the structure allows it, add overflow scuppers where the code wants them, and keep the field draining so the warranty actually means something. If a storm has already opened up your roof and you need it watertight today, our storm restoration crew tarps and dries-in the building first, and if the damage is a claim, our insurance claims team documents the field for your adjuster. For smaller flat fields and low-slope sections, our commercial flat roof work covers built-up and single-ply repair and replacement.
Built right, then stood behind
An industrial roof is a big number and a long bet, so the people who put it on should still be standing behind it years later. We are an OSHA-certified crew, which on a working facility is not a box to check: it means the work happens safely above your people and your forklift traffic, to code, not in a hurry by whoever was available. The ventilation on every roof we build follows our Lomanco-certified design, because a roof over a baking, unvented plenum still fails early no matter how good the field is.
Every industrial roof we install carries a lifetime workmanship warranty, so the quality of our installation is covered for as long as you own the building. On top of that we include six years of weatherproofing done annually, where we come back, walk the field, check the seams, curbs, drains and fasteners, and seal anything that has moved before it can leak into the operation. On a facility where a single overnight leak can cost more than the repair, that yearly visit is the part of the job that pays for itself, and it is the part most roofers skip the moment the check clears.
Industrial roofing questions
Straight answers about downtime, phasing, recovery and warranty. If yours is not here, call (432) 288-5562 or send it through our contact page.
Can you re-roof our building while we keep operating?
Yes. We phase industrial re-roofs around your schedule, section the work so the crew stays over empty or low-activity bays, and keep the building dried-in overhead at the end of every workday. Loud or disruptive work gets scheduled off-shift where it matters. Most facilities we re-roof never stop production.
Can you recover over our existing roof instead of tearing it off?
Sometimes. If the existing roof is structurally sound and the building code allows another layer, a recover saves time and money and keeps the field watertight throughout. If the deck or insulation is wet or the structure is questionable, a tear-off is the honest answer. We tell you which one your roof has earned after we walk it, not before.
What kind of industrial roofs do you work on?
Pre-engineered metal building roofs, standing-seam and exposed-fastener metal over steel framing, and the large low-slope single-ply membrane fields on warehouses and plants. We handle metal panel replacement, re-fastening, membrane repair and full replacement, and the flashing and drainage work that keeps any of them dry.
Why does our flat warehouse roof keep ponding water?
Standing water on a low-slope field usually means the slope to the drains has flattened over time, or the drains and scuppers are undersized or blocked. Ponding is what kills membrane and corrodes metal early. When we re-roof we correct the slope to the drains where the structure allows it and add overflow scuppers where the code wants them.
Do you handle storm damage and insurance on industrial roofs?
Yes. If a storm has opened up your roof we tarp and dry-in the building first so the operation stays protected, then assess the field. When the damage is a claim, our insurance team photographs and documents the roof for your adjuster so the scope reflects what the building actually needs.
How far does Plenox travel for industrial roofing?
We are based in Leander, TX and cover the Austin metro plus jobs statewide across TX. If your facility is outside the metro and you are not sure you are in range, reach out through our contact page or call and we will tell you straight.
Ready for an industrial roof done once
Tell us about the building and what the roof is doing now. We will come walk the field, talk through metal versus membrane, recover versus tear-off, and put a clear number and a phasing plan on paper. Your free roof quote costs nothing and you are under no obligation. See finished work in our project gallery.
Serving Leander and statewide TX
We roof warehouses, plants and facilities across the Austin metro and out across Texas from our Leander shop. A few of the cities we work in: